• 设备
    • 今日
    • 0

    cisco常用查看端口命令

    cisco路由器常用的查看端口和通道状况的命令


     

    下面以Cisco1800路由器为例,介绍一下常用的查看端口和通道状况的命令。 在MS-DOS窗口里敲入命令telnet+IP地址,回车,即可远程登录路由器。一般用路由器局域网口地址。

    1,用R1#sh ip int b命令查看端口状态
    R1#sh ip int b
    Interface IP-Address OK? Method Status Protocol
    FastEthernet0/0 100.100.100.226 YES NVRAM up up
    FastEthernet0/1 200.200.200.226 YES NVRAM up up
    Serial0/0/0 72.22.81.102 YES NVRAM up up
    Serial0/0/1 72.22.81.109 YES NVRAM up up
    正常情况下,思科1800路由器四个端口的Statusprotocol都是up的。

    2,用R1#sh int s0/0/0查看链路状态和通道情况
    Serial0/0/0 is up, line protocol is up //接口与协议都已启动(正常)
    Serial0/0/0 is up, line protocol is down //
    接口启动,协议没有匹配成功(端口无物理故障,但通道不通)
    Serial0/0/0 is down, line protocol is down
    notconnect//接口与协议都DOWN,本端端口没有与对方建立物理连接,可能是对方设备没有开启,对方端口故障或者线路故障造成。
    Serial0/0/0 is down, line protocol is down //
    接口与协议都DOWN掉(协转没有工作)
    Serial0/0/0 is down,line protocol is down
    disable//端口出现物理性故障,需更换端口。
    Serial0/0/0 is administratively down,line protocol is down //
    接口关闭,可用命令打开。
    Serial0/0/0 is up, line protocol is down
    looped //此通道上有环(无论在协转、DDF架、SDH上做环,在路由器里看到的显示是一样的)。

    Serial0 is up, line protocol is down
    Hardware is PowerQUICC Serial
    Interface is unnumbered. Using address of FastEthernet0/0 (172.22.128.193)
    MTU 1500 bytes, BW 1544 Kbit, DLY 20000 usec,
    reliability 255/255, txload 1/255, rxload 1/255 //
    通道的可靠性
    Encapsulation PPP, LCP Listen, loopback not set
    Last input 00:00:27, output 00:00:27, output hang never
    Last clearing of "show interface" counters 00:02:52 //
    上次计数器清零到现在的时间
    Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
    Queueing strategy: weighted fair
    Output queue: 0/1000/64/0 (size/max total/threshold/drops)
    Conversations 0/2/256 (active/max active/max total)
    Reserved Conversations 0/0 (allocated/max allocated)
    Available Bandwidth 1158 kilobits/sec
    5 minute input rate 0 bits/sec, 0 packets/sec
    5 minute output rate 0 bits/sec, 0 packets/sec
    30 packets input, 420 bytes, 0 no buffer
    Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
    6552 input errors, 0 CRC, 4 frame, 0 overrun, 0 ignored, 0 abort//
    输入错误包数量
    60 packets output, 840 bytes, 0 underruns
    0 output errors, 0 collisions, 9 interface resets
    0 output buffer failures, 0 output buffers swapped out
    0 carrier transitions
    DCD=up DSR=up DTR=up RTS=up CTS=up
    通道的可靠性,正常值是255/255,如果低于254将会造成丢包。可靠性越低,通道越差,错误包越多。

    DCD
    数据载体检测DTE CARrfer derect
    DSR
    数据设置就绪DATA SET READY
    DTR
    数据终端就绪DTE IS READY
    RTS
    请求发送Reguest To Send
    CTS
    清除发送Clear To send

    3,路由器端口计数器清零
    有故障的通道往往造成路由器接口的输入错误包数量很高,不便于比较查看。这时最好把接口数据包计数器清零,使其重新开始计数。用R1#clear coun命令清零。
    R1#clear coun

    4,判断以太网端口故障
    R1#sh int f0/0 来检查以太网口及其链路的状态,如下所示:
    R1#sh int f0/0
    FastEthernet 0 is up,line protocol is up //
    连接正常
    Ethernet 0 is up,line protocol is down //
    连接故障,路由器没有连接到局域网
    Ethernet 0 is down,line protocol is down(disable) //
    接口故障
    Ethernet 0 is administratively down,line protocol is down //
    接口被关闭,可用命令打开

    5,查看相邻路由器
    R2#sh cdp nei命令查看相邻路由器,输出如下:
    R2#sh cdp nei
    Capability Codes: R - Router, T - Trans Bridge, B - Source Route Bridge
    S - Switch, H - Host, I - IGMP, r - Repeater
    Device ID Local Intrfce Holdtme Capability Platform Port ID
    R1 Ser 0/0/0 133 R S I 1841 Ser 0/0/1
    S2_SW1 Fas 0/0 125 S I WS-C2960-2Fas 0/6
    S2_SW2 Fas 0/1 140 S I WS-C2960-2Fas 0/22
    R3 Ser 0/0/1 156 R S I 1841 Ser 0/0/0
    此命令可以查看到相邻的思科路由器和思科
    交换机,可以验证设备是否相通,以及连接关系是否正确。

    6,观察路由器告警和报错信息
    路由器发生故障或状态发生变化的时候,会发出告警、报错、提示信息。如果是用telnet命令登录路由器的话,不能直接看到这些信息,需要输入R1# ter mon命令后,才能使这些信息显示在MS-DOS窗口上。
    R1#ter mon
    该命令可以使你及时了解路由器状态变化,便于发现和排除故障。

     

    来自:PC 局域网
    上一篇: cisco交换机如何查找环路及解决方法
    您可能还喜欢这些:

    亲,沙发正空着,还不快来抢?

    评论审核已开启:即评论经审核才能正常显示! 记住我的个人信息 回复后邮件通知我